Fiasco Radio

Problems With Clock Radios?



Sometimes alarm clock radios break down. However, we can take the time to repair them ourselves. The following is what to do to repair them.

 1. Check the power at the outlet, and make sure the power is on.

2. Check the pointer. Some household radios use a station frequency pointer mounted on a dial cord that is moved by a small wheel on the side of the clock radio. Other household radios use a digital frequency readout that cannot be adjusted.

3. If the sound is fuzzy, disassemble the unit and locate the volume control. Spray electrical contact cleaner into the control and rotate or slide the control several times to lubricate the mechanism.

4. Replace a damaged or broken antenna.

Most modern clock radios are built on printed circuit boards that can only be repaired by trained technicians. Some of the tools you may need are screwdrivers, wrenches, electronic control cleaner, denatural alcohol, soldering iron and solder.

Reset Dial Pointer

1. Turn on radio. Find a strong radio signal, listen to the frequency.

 

2. Use a piece of tape or grease pencil to mark the dial where the pointer should be for that frequency.

 

3. Unplug the receiver and open the housing. There are usually two to four screws in the underside of the radio.

 

4. Inspect the pointer mechanism for problems, such as a cord that came off at the end rollers, or a break in the cord. Replace the broken cord or repair it.

 

5. Loosen the spring clips Move the pointer along the dial cord until the station being received lines up with the tape or mark on the dial.

 

6.Tighten the clips on the cord. Make sure you do not move the pointer.

 

7. Plug the radio in and verify that the dial pointer reads correctly.

Replacing External Antenna

1. Loosen the antenna screw.

 

2. If there is no exterior screw, open the radio and access the antenna base.

Replacing an Internal Antenna

1. Unplug the receiver and open the housing.

 

2. Find and remove the internal antenna, of the internal base of the external antenna.

 

3. Inspect the wires wound around the antenna for serious damage. Make sure the antenna is firmly plugged into the main circuit board. If the antenna is damaged, replace it or attempt to repair the antenna, or replace the radio as a unit.

Clean Electronic Components

1. Unplug the receiver and open the housing.

 

2. Use canned air to blow dust from components, including any power cords and speaker jacks.

 

3. Use electrical contact cleaner, or a cotton swab dipped in dentured alcohol to clean electronic components.

 

4. If you find broken components on a circuit board, replace the circuit board. Before purchasing a circuit board, you can use a soldering iron and electronic solder to attempt a repair.

 

Now you have repaired the clock radio yourself.

 

Sometimes alarm clock radios break down. However, we can take the time to repair them ourselves. The following is what to do to repair them.

 

1. Check the power at the outlet, and make sure the power is on.

]]>

 

2. Check the pointer. Some household radios use a station frequency pointer mounted on a dial cord that is moved by a small wheel on the side of the clock radio. Other household radios use a digital frequency readout that cannot be adjusted.

 

3. If the sound is fuzzy, disassemble the unit and locate the volume control. Spray electrical contact cleaner into the control and rotate or slide the control several times to lubricate the mechanism.

 

4. Replace a damaged or broken antenna.

 

Most modern clock radios are built on printed circuit boards that can only be repaired by trained technicians. Some of the tools you may need are screwdrivers, wrenches, electronic control cleaner, denatural alcohol, soldering iron and solder.

Reset Dial Pointer

1. Turn on radio. Find a strong radio signal, listen to the frequency.

 

2. Use a piece of tape or grease pencil to mark the dial where the pointer should be for that frequency.

 

3. Unplug the receiver and open the housing. There are usually two to four screws in the underside of the radio.

 

4. Inspect the pointer mechanism for problems, such as a cord that came off at the end rollers, or a break in the cord. Replace the broken cord or repair it.

 

5. Loosen the spring clips Move the pointer along the dial cord until the station being received lines up with the tape or mark on the dial.

 

6.Tighten the clips on the cord. Make sure you do not move the pointer.

 

7. Plug the radio in and verify that the dial pointer reads correctly.

Replacing External Antenna

1. Loosen the antenna screw.

 

2. If there is no exterior screw, open the radio and access the antenna base.

Replacing an Internal Antenna

1. Unplug the receiver and open the housing.

 

2. Find and remove the internal antenna, of the internal base of the external antenna.

 

3. Inspect the wires wound around the antenna for serious damage. Make sure the antenna is firmly plugged into the main circuit board. If the antenna is damaged, replace it or attempt to repair the antenna, or replace the radio as a unit.

Clean Electronic Components

1. Unplug the receiver and open the housing.

 

2. Use canned air to blow dust from components, including any power cords and speaker jacks.

 

3. Use electrical contact cleaner, or a cotton swab dipped in dentured alcohol to clean electronic components.

 

4. If you find broken components on a circuit board, replace the circuit board. Before purchasing a circuit board, you can use a soldering iron and electronic solder to attempt a repair.

 

Now you have repaired the clock radio yourself.

 

Sometimes alarm clock radios break down. However, we can take the time to repair them ourselves. The following is what to do to repair them.

 

1. Check the power at the outlet, and make sure the power is on.

 

2. Check the pointer. Some household radios use a station frequency pointer a dial cord that is moved by a small wheel on the side of the clock radio. Other household radios use a digital frequency readout that cannot be adjusted.

3. If the sound is fuzzy, disassemble the unit and locate the volume control. Spray electrical contact cleaner into the control and rotate or slide the control several times to lubricate the mechanism.

 

4. Replace a damaged or broken antenna.

Most modern clock radios are built on printed circuit boards that can only be repaired by trained technicians. Some of the tools you may need are screwdrivers, wrenches, electronic control cleaner, denatural alcohol, soldering iron and solder.

Reset Dial Pointer

1. Turn on radio. Find a strong radio signal, listen to the frequency.

 

2. Use a piece of tape or grease pencil to mark the dial where the pointer should be for that frequency.

 

3. Unplug the receiver and open the housing. There are usually two to four screws in the underside of the radio.

 

4. Inspect the pointer mechanism for problems, such as a cord that came off at the end rollers, or a break in the cord. Replace the broken cord or repair it.

 

5. Loosen the spring clips Move the pointer along the dial cord until the station being received lines up with the tape or mark on the dial.

 

6.Tighten the clips on the cord. Make sure you do not move the pointer.

 

7. Plug the radio in and verify that the dial pointer reads correctly.

Replacing External Antenna

1. Loosen the antenna screw.

 

2. If there is no exterior screw, open the radio and access the antenna base.

Replacing an Internal Antenna

1. Unplug the receiver and open the housing.

 

2. Find and remove the internal antenna, of the internal base of the external antenna.

 

3. Inspect the wires wound around the antenna for serious damage. Make sure the antenna is firmly plugged into the main circuit board. If the antenna is damaged, replace it or attempt to repair the antenna, or replace the radio as a unit.

Clean Electronic Components

1. Unplug the receiver and open the housing.

 

2. Use canned air to blow dust from components, including any power cords and speaker jacks.

 

3. Use electrical contact cleaner, or a cotton swab dipped in dentured alcohol to clean electronic components.

 

4. If you find broken components on a circuit board, replace the circuit board. Before purchasing a circuit board, you can use a soldering iron and electronic solder to attempt a repair.

 

Now you have repaired the clock radio yourself.

 

TheWatchTheClock.Com

 

Source: ArticlesBase.com

Boost Your Sales with Affordable Radio Advertising Leeds

Who says is gone for good? Contrary to popular belief, radio advert is alive and beefing up many small and home businesses. Despite the wide use of television and the Internet, effective radio advertising remains the most effective method of reaching a local marketplace say a small town or city. This is because thousands of people in Leeds continue to own and use the radio, and can be effectively reached through radio commercials and announcements. presents a range of benefits for small business owners like you who want to boost sales through cost-effective promotional methods. Advertising is a must expense whatever type of business you operate, and whether you are catering the market in Leeds or somewhere else. If your small business is not getting the revenue level you expect, perhaps what you need is to tap radio advert strategies.

Now, you may not be convinced how can solve your profitability concerns, so here are some things you need to learn. First off, radio advertising has wider local coverage in Leeds. Regional radio stations such as Radio Aire, Magic 828 and Yorkshire Radio have offices in the city. Also, several communities within the city and surrounding areas run local radio stations. As mentioned earlier, a large part of the population in the city listen to the radio. Second, radio advert is substantially cheaper than other advertising media. Most of the radio stations in Leeds offer cheap radio advertising packages to small and home businesses. You can take advantage of the affordable rates and wider scopes that radio stations have within a local area.

Third, radio campaign offers more precise targeting of the audience. It is relatively easier to determine the type of listeners a station has. Each station targets a specific demographic, so there is little to no need for targeting marketing efforts. The initial thing needed here is to identify which stations your prospect buyers mostly listens to. Afterwards, you need to sort out which of stations offer the most campaign. Fourth reason why radio advert is a great marketing method is that radio stations usually provide all-inclusive advertising package. This means that everything you need to produce and air a radio commercial is provided for, from script writing to commercial production. Also, some stations offer you data about whether your radio campaign was effective or not.

Fifth, can be used to market a wide range of products and services. Regardless of what you are selling, you can successfully promote it via radio campaign. Sixth, radio jockeys are regarded as reliable endorsers by their listeners. This means that if you have your products or services announced or endorsed by your target market’s favorite jockeys, you have a good chance of making sales. Plus, radio jockeys normally do not charge very high fees for announcing product launches, promotional sales, press conferences, charity activities, and other commercial events. All the better for you and your small business to maximize cheap radio advertising campaign.

Source: ArticlesBase.com